Welcome to East Point Trader! New Jersey's best supplier of:

Dock Hardware

Standard Gradge (3/16") and Commercial Grade (1/4") Tie Down Dock Hardware is designed for use with 1-1/2" thick lumber (minimum width 6"). All hardware is mounted with 3/8" carriage bolts. All male and female dock to dock connections are made with either 3/4" bolts with lock nuts or 3/4" connecting pins. Tie Downs' Wood Dock Plan Kit will show you the basics on building a lightweight and long lasting floating dock system.


Lag Bolt Set

Bolt and flast washer hot dip galvanized used to attach flotation durms to dock system.

  • Standard / Commerical - 3/8" x 2"
  • Standard / Commerical - 3/8" x 3"
  • Standard / Commerical - 3/8" x 5"

Carriage Bolt Set

Set includes carriage bolt, flat washer and nut. Hot dip galvanized.

  • Standard Grade - 3/8" x 2-1/2"
  • Commerical Grade - 1/2" x 3"
  • Commerical Grade - 1/2" x 5"

Hex Head Bolt Set

Includes nut. Used to connect male and female. T connectors.

  • Galvanized 3/4" x 3-1/2".

Connector Pin Set

For quick disconnect. Used to connect male and female T connectors.

  • Galvanized 3/4" connector pin and hits clip pin

Outside Corner / Female

Use with a male outside corner. Each leg is 10"L x 5"H.

  • Standard Grade - 1/2" welded tabs
  • Commerical Grade - 1/2" welded tabs

Outside Corner / Male

Use with female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5"H

  • Standard grade - 1/2" welded tab
  • Commerical Grade - 1/2" welded tab
  • Commerical Grade - 3/4" welded tab

Outside Corner End

Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners

  • Standard Grade - 10"L x 5"H
  • Commerical Grade - 10"L x 5"H
  • Commerical Grade - 12 - 1/4"L x 5"H

Inside Rolling Ramp Bracket

5"x 11 x 1/4" galvanized steel includes left and right ramp brackets

Male T Connector

Has one welded 1/2" tab. Use with female T connector to attach fingers and ramps, 5"L x 5"H. 3/4" bolt set required for joint.

  • Standard Grade .438" Square Holes 3.5 OC
  • Commerical Grade .562" Square Holes 3.5 OC
  • Commerical Grade with 3/4" tab .562" Square Holes 3.5" OC

Female T Connector

Has two welded 1/2" tabs. Bolts to side of dock to attach fingers and ramps. Measures 5"L x 5"H.

  • Standard Grade .438" Square Holes 3.5 OC
  • Commerical Grade .562" Square Holes 3.5 OC

Washer Plate

Use tow washer plates with each angle. Measures 1-1/2"L x 5"H.

  • Standard Grade .438" Square Holes 3.5" OC
  • Commerical Grade .562" Square Holes 3.5 OC

Back Up Plate

5"x5" reinforcing plates are used to back up the single T males and females

  • Commerical Grade .562" Square Holes 3.5" OC

Inside Corner Pipe Holder

These heavy duty inside corner pipe holders can be used with one of the outside corner brackets. Tie Down offers both standard and commerical versions of 2"ID. or 3"ID. pipe holders. Measures 8-1/2"L x 5"H. Requires carriage bolt set for attaching.

  • Inside Corner Pipe Holder 2" ID. Standard and Commercial Grade
  • Inside Corner Pipe Holder 3" ID. Standard and Commercial Grade

Outside Pipe Holder

Pipe Holder bolts to the outside of the dock. Carriage bolt set required for attaching. Pipe Holder has a 3" ID. for use with 2" pipe to hold dock in place.

  • Standard Grade
  • Commerial Grade

Chain Retainer

Bolts to side of dock. Use weights and chains to hold dock in place. Accomodations 1/4", 3/8", & 1/2" chains. Measures 5"L x 5"H

  • Standard Grade
  • Commerial Grade

 

Piling Hoop

Heavy Duty 1/4 galvanized steel x 3" high

  • Commerical Grade 14"x3 with 4" radius for 8" Piles
  • Commerical Grade 16"x3 with 5" radius for 10" Piles
  • Commerical Grade 18"x3 with 6" radius for 12" Piles
  • Commerical Grade 20"x3 with 7" radius for 14" Piles

Backing Plate / Hurricane Strap

Standard Grade

  • Backing plate - 4"x 18" x 7 ga.
  • Backing plate - 2"x 18" x 7 ga.

 

Deck Plate

Heavy Duty Deck Plate for use with piling hoop. This 3/16" thick 4"x6" angle can be bolted from the top and side of the dock. The hoop can then be bolted to the angle, allowing it to be removed seasonally. 22" long. Commerical grade.

Piling Hoop

Heavy Duty Piling Hoop for pilings up to 12" in diameter. The hoop is constructed of 1-1/2" pipe and is hot dip galvanized. It can be bolted directly to the side of the dock or tot he optional Deck Plate. Commerical Grade.

Roller Assembly

Heavy duty roller assembly that can be mounted directly to dock or to deck plates. Assembly contains a 5/8" stainless steel roller shaft with removable cotter pins and a 6"/12" black rubber roller.

  • 6" Roller Commerical Grade

Piling Hoop and Roller

Piling Hoop and Roller Assembly intended for areas with lots of wind, current, or tidal action. Combines the piling hoop and roller assembly to make up and down movement easier. For pilings up to 12" in diameter. Commerical Grade.

Piling Hoop

2" round steel piling hoop with 3/8" welded mounting tabs can be secured directly to dock with carriage bolts or with the Universal Deck Plate to allow easy removeal and a more secure attachment point.

  • Commerical Grade 12"
  • Commerical Grade 14"
  • Commerical Grade 16"

Universal Deck Plate

Heavy duty universal deck plate has slots that allow use with any of the piling hoops listed above. Plate measures 24" L x 6" Top x 5" side and is sized to be bolted to dock from top and side. Holes and slots allow top and side mounting of roller assembly part. Commerical Grade.

14" Hoop Roller Pile Holder

With a 12-1/2" interior width this pile holder can be used with piling up to 14" in diameter. A 12" durable poly-vinyl roller mounted on a 1-1/4" diameter shaft will provide years of service. Overall dimensions of part are 24-1/4" x 22-1/2".

Chain Pile Holder

For use as a pile holder with 3/8" galvanized chain and shackles. Can be adjusted for various pile diameters. 20-1/4" x 4-1/4" x 4-1/4 x 1/4 Steel. Commerical Grade.

14" Internal Pile Holder

The interior width of 14", pile holder will allow it to be used with piling up to 13-1/2" in diameter. Four 6" rubber rollers allow dock movement for usage in tidal areas or where water level change. Overall dimensions of part are 24" x 24" x 7-15/16". Commerical Grade.

Piling Rod / Ring

Piling rod for us in mooring boats where tidal changes and fluctuating water levels require a moveable tethering point. Rods are used in conjunction with a 1/2" by 4" steel ring. Rod consists of a solid 1.0" steel bar welded to two 3/8"x 3" mounting plates. Holes in mounting plates are sized for use of 5/8 bolts. Hot dipped galvanized finish will provide superior corrosion protection.

  • Commerical Grade 5'
  • Commerical Grade 6'

Inside Corner

This heavy duty inside corner should be used with one of the outside corners.

  • Standard Grade 8-1/4"L x5"H with 2" elongate holes
  • Commercial Grade 8-1/4"L x5"H with 2-1/4 " elongate holes
  • Commercial Grade 8-1/4"L x5"H with 3" elongate holes
  • Commercial Grade 8-1/4"L x5"H with square holes
  • Commercial Grade 10-1/2"L x 5"H with 2-1/4"
  • Commerical Grade 8-1/4" L x 5"H with 2-1/4"

Don't see the size you need? Ask us!