Welcome to East Point Trader! New Jersey's best supplier of:
Lag Bolt SetBolt and flast washer hot dip galvanized used to attach flotation durms to dock system.
|
Carriage Bolt SetSet includes carriage bolt, flat washer and nut. Hot dip galvanized.
|
Hex Head Bolt SetIncludes nut. Used to connect male and female. T connectors.
|
Connector Pin SetFor quick disconnect. Used to connect male and female T connectors.
|
Outside Corner / FemaleUse with a male outside corner. Each leg is 10"L x 5"H.
|
Outside Corner / MaleUse with female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5"H
|
Outside Corner EndUse this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners
|
Inside Rolling Ramp Bracket5"x 11 x 1/4" galvanized steel includes left and right ramp brackets |
Male T ConnectorHas one welded 1/2" tab. Use with female T connector to attach fingers and ramps, 5"L x 5"H. 3/4" bolt set required for joint.
|
Female T ConnectorHas two welded 1/2" tabs. Bolts to side of dock to attach fingers and ramps. Measures 5"L x 5"H.
|
Washer PlateUse tow washer plates with each angle. Measures 1-1/2"L x 5"H.
|
Back Up Plate5"x5" reinforcing plates are used to back up the single T males and females
|
Inside Corner Pipe HolderThese heavy duty inside corner pipe holders can be used with one of the outside corner brackets. Tie Down offers both standard and commerical versions of 2"ID. or 3"ID. pipe holders. Measures 8-1/2"L x 5"H. Requires carriage bolt set for attaching.
|
Outside Pipe HolderPipe Holder bolts to the outside of the dock. Carriage bolt set required for attaching. Pipe Holder has a 3" ID. for use with 2" pipe to hold dock in place.
|
Chain RetainerBolts to side of dock. Use weights and chains to hold dock in place. Accomodations 1/4", 3/8", & 1/2" chains. Measures 5"L x 5"H
|
Piling HoopHeavy Duty 1/4 galvanized steel x 3" high
|
Backing Plate / Hurricane StrapStandard Grade
|
Deck PlateHeavy Duty Deck Plate for use with piling hoop. This 3/16" thick 4"x6" angle can be bolted from the top and side of the dock. The hoop can then be bolted to the angle, allowing it to be removed seasonally. 22" long. Commerical grade. |
Piling HoopHeavy Duty Piling Hoop for pilings up to 12" in diameter. The hoop is constructed of 1-1/2" pipe and is hot dip galvanized. It can be bolted directly to the side of the dock or tot he optional Deck Plate. Commerical Grade. |
Roller AssemblyHeavy duty roller assembly that can be mounted directly to dock or to deck plates. Assembly contains a 5/8" stainless steel roller shaft with removable cotter pins and a 6"/12" black rubber roller.
|
Piling Hoop and RollerPiling Hoop and Roller Assembly intended for areas with lots of wind, current, or tidal action. Combines the piling hoop and roller assembly to make up and down movement easier. For pilings up to 12" in diameter. Commerical Grade. |
Piling Hoop2" round steel piling hoop with 3/8" welded mounting tabs can be secured directly to dock with carriage bolts or with the Universal Deck Plate to allow easy removeal and a more secure attachment point.
|
Universal Deck PlateHeavy duty universal deck plate has slots that allow use with any of the piling hoops listed above. Plate measures 24" L x 6" Top x 5" side and is sized to be bolted to dock from top and side. Holes and slots allow top and side mounting of roller assembly part. Commerical Grade. |
14" Hoop Roller Pile HolderWith a 12-1/2" interior width this pile holder can be used with piling up to 14" in diameter. A 12" durable poly-vinyl roller mounted on a 1-1/4" diameter shaft will provide years of service. Overall dimensions of part are 24-1/4" x 22-1/2". |
Chain Pile HolderFor use as a pile holder with 3/8" galvanized chain and shackles. Can be adjusted for various pile diameters. 20-1/4" x 4-1/4" x 4-1/4 x 1/4 Steel. Commerical Grade. |
14" Internal Pile HolderThe interior width of 14", pile holder will allow it to be used with piling up to 13-1/2" in diameter. Four 6" rubber rollers allow dock movement for usage in tidal areas or where water level change. Overall dimensions of part are 24" x 24" x 7-15/16". Commerical Grade. |
Piling Rod / RingPiling rod for us in mooring boats where tidal changes and fluctuating water levels require a moveable tethering point. Rods are used in conjunction with a 1/2" by 4" steel ring. Rod consists of a solid 1.0" steel bar welded to two 3/8"x 3" mounting plates. Holes in mounting plates are sized for use of 5/8 bolts. Hot dipped galvanized finish will provide superior corrosion protection.
|
Inside CornerThis heavy duty inside corner should be used with one of the outside corners.
|